Landracing Forum

Misc Forums => NON LSR Posting => Topic started by: Peter Jack on January 11, 2012, 04:21:42 AM

Title: Looking for a Source
Post by: Peter Jack on January 11, 2012, 04:21:42 AM

I'm looking for a source for the oval aluminum tubing shown in the picture or something similar. The tubing is about 18 mm on the short axis and about 35 mm on the long axis with a 2 mm wall (all measurements taken with a tape). I'm also looking for a larger size that this one will slip into, preferably with a reasonably decent fit. I need about ten feet of each. It must be a weldable alloy.

Any help would be greatly appreciated.

Thanks,
Pete

Title: Re: Looking for a Source
Post by: Tman on January 11, 2012, 09:46:43 AM

You try Aircraft Spruce?

Title: Re: Looking for a Source
Post by: Peter Jack on January 11, 2012, 10:43:23 AM

That was my very first try Trent. They have aerodynamic tubing in one size but not the symmetrical tubing I'm looking for. I also need a little more wall thickness than generally found in aircraft. There's going to be a small compression loading on the tubing lengthwise and some angular loading although neither is great.

Pete

Title: Re: Looking for a Source
Post by: Bob Drury on January 11, 2012, 11:22:13 AM

  Pete, you might try searching the net for custom aluminum extrusions or extruders cause you ain't going to get this from Ace Hardware...............   Bob

Title: Re: Looking for a Source
Post by: Tman on January 11, 2012, 11:24:31 AM

This came up here or on the HAMB, I forget. I seem to remember cromo being ran through a rollar and ovalized. Might have been a Ron Covell deal?

Title: Re: Looking for a Source
Post by: Tman on January 11, 2012, 11:58:03 AM

Doing some searching for you PJ. Here is some streamline stuff I found. All taken off HAMB searches.

http://secure.chassisshop.com/partlist/5913/



http://www.californiasteelandtube.com/Tubing_Packaging_Chart.htm

Here is the home brew version!

http://www.jalopyjournal.com/forum/showthread.php?t=181221&highlight=oval+tubing

Title: Re: Looking for a Source
Post by: Peter Jack on January 11, 2012, 12:27:24 PM

Thanks Trent. The tubing has to be aluminum and the shape symmetrical. I may try a short test piece using the home brew method.

The funny thing about that is that I used to follow the Kansas City Dawn Patrol guys fairly regularly when I used to read Kitplanes Magazine. They do some scary stuff, but they're also pretty innovative and not afraid to try something. It's just that I want to be really close to the ground when I'm trying something a little different.

Boy do I ever like the way the spell check works now. :-D :-D :-D

Pete

Title: Re: Looking for a Source
Post by: Tman on January 11, 2012, 12:32:31 PM

Let us know if it works for you! :cheers:

Title: Re: Looking for a Source
Post by: Stan Back on January 11, 2012, 12:34:27 PM

Ill chick if it work's four ewe.

Title: Re: Looking for a Source
Post by: WOODY@DDLLC on January 11, 2012, 12:51:24 PM

Nothing on their webpage yet but they were showing oval tubing at IMIS this year.

www.twmetals.com

Title: Re: Looking for a Source
Post by: Peter Jack on January 11, 2012, 12:59:27 PM

It obviously works as it lets all of Stan's legitimate words through!  :-D :-D :-D

Pete

Title: Re: Looking for a Source
Post by: Cajun Kid on January 13, 2012, 06:38:45 PM

Stan uses legitimate words ?  :? :? :? :?