Landracing Forum Home
May 19, 2013, 11:26:09 AM *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
News:
BACK TO LANDRACING.COM HOMEPAGE
 
   Home   Help Search Calendar Login Register  

(Note: Donations are not tax deductible)
Landracing Forum Home > Tech Information > Technical Discussion (Moderator: Seldom Seen Slim) > 4wd `liner drive shaft enclosure
Pages: [1]   Go Down
« previous next »
  Print  
Author Topic: 4wd `liner drive shaft enclosure  (Read 1199 times)
0 Members and 1 Guest are viewing this topic.
floydjer
Hero Member
*****
Offline Offline

Age: 55
Location: grand rapids, michigan
Posts: 970


"There is no duck side of the moon..."




Ignore
« on: October 06, 2009, 10:53:54 AM »
My streamliner project is mid-engine (behind cockpit,forward of rear axle)and 4 wheel drive .In the area where the front drive shaft passes along the outside of the cockpit, I`m planning on having the shaft and all couplers inside .250 wall d.o.m. tube w/ smaller dia. tube inside mounted with  1/4 in. bolts. My thinking is the smaller tube will act like the liner in a  T/F drag car clutch can and spin . Thoughts/ Comments?  J.B.
« Last Edit: November 04, 2009, 08:09:35 AM by floydjer » Logged
I`d never advocate drugs,alcohol,violence or insanity to anyone...But they work for me.
floydjer
Hero Member
*****
Offline Offline

Age: 55
Location: grand rapids, michigan
Posts: 970


"There is no duck side of the moon..."




Ignore
« Reply #1 on: November 03, 2009, 02:57:11 PM »
173 views and not even a like/dis-like??? huh
Logged
I`d never advocate drugs,alcohol,violence or insanity to anyone...But they work for me.
RichFox
Hero Member
*****
Offline Offline

Location: San Mateo, Ca
Posts: 1834





Ignore
« Reply #2 on: November 03, 2009, 03:07:36 PM »
It sounds good to me. Lots of steel between the driver and the shaft has to be a good thing. I guess everybody else thinks the same. We only like to jump in with "You can't do that" comments.
Logged
jl222
Hero Member
*****
Offline Offline

Location: Clovis calif.
Posts: 1881




Ignore
« Reply #3 on: November 03, 2009, 03:16:08 PM »

  Yea that sounds good, you going to use a funny car type drive shaft? How do you disconnect and reconnect to ring and pinion assuming drive shaft is offset.

           JL222
Logged
Peter Jack
Hero Member
*****
Offline Offline

Age: 69
Location: Calgary, Alberta
Posts: 2113





Ignore
« Reply #4 on: November 03, 2009, 10:01:26 PM »
When you're on the right track you don't attract a lot of comment.

Pete
Logged
My avatar shows Tok, a 100# Alaskan Malamute.
He's the one who runs everything around here.
Mr411Fan
Newbie
*
Offline Offline

Posts: 48





Ignore
« Reply #5 on: November 03, 2009, 10:14:44 PM »
Somewhere I have some pictures from the FIA meet where Tom Burkland broke the front driveshaft U-joint, and thier shield protected the driver very well.  The shaft runs right next to the drivers leg.  I don't remember the construction particulars, but it was tested.  The inner liner sounds like a good idea.
Herb
Logged
floydjer
Hero Member
*****
Offline Offline

Age: 55
Location: grand rapids, michigan
Posts: 970


"There is no duck side of the moon..."




Ignore
« Reply #6 on: November 04, 2009, 08:19:34 AM »
Thought for a moment I`d been "silenced".  The rear trans. mount is aluminum plate much like an engine mounting plate, with the left side extending outside of the frame rails. Alum. drive hubs connected by belts to off-set the power to the forward shaft and the same at the front to get back to the center line of the front dif. Splined shafts w/ couplers and no u-joints.  :cheers:J.B.
Logged
I`d never advocate drugs,alcohol,violence or insanity to anyone...But they work for me.
Pages: [1]   Go Up
  Print  
« previous next »
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.18 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!


Google visited last this page May 16, 2013, 07:47:06 AM