Author Topic: Motorcycle chain Master link question  (Read 3431 times)

0 Members and 1 Guest are viewing this topic.

Offline 07R1LSR

  • Full Member
  • ***
  • Posts: 124
Motorcycle chain Master link question
« on: February 16, 2020, 06:24:53 PM »
Searched the forum and didn't come up with much.  Does anyone know the requirements for the chain master link type?  Curious if it is a scrutinized item or if any master link will work. 
Thanks again!

Offline Stainless1

  • Administrator
  • Hero Member
  • ***
  • Posts: 8948
  • Robert W. P. "Stainless" Steele
Re: Motorcycle chain Master link question
« Reply #1 on: February 16, 2020, 10:05:04 PM »
I always liked the rivet type, but any type is allowed I believe... if you use a clip, try to seal it on.
 :cheers:
Stainless
Red Hat 228.039, 2001, 65ci, Bockscar Lakester #1000 with a little N2O

Offline 07R1LSR

  • Full Member
  • ***
  • Posts: 124
Re: Motorcycle chain Master link question
« Reply #2 on: February 16, 2020, 10:40:39 PM »
Thanks again Stainless!

Offline stay`tee

  • Sr. Member
  • ****
  • Posts: 613
  • "Kawasaki ZX12 Turbocharged"
Re: Motorcycle chain Master link question
« Reply #3 on: February 17, 2020, 05:09:11 AM »
After 50 years of Dragracing (8 second turbo bikes) and now almost 15 years LandSpeed (200mph bikes),, I have "always" used links, and "never" had a failure,,

Always ensure the c clips are not stretched, and always wipe the outer link surface and clip with Shellite before applying a sealent
First Australian to ride a motorcycle over 200mph at Bonneville,,,

Offline Koncretekid

  • Hero Member
  • *****
  • Posts: 1203
Re: Motorcycle chain Master link question
« Reply #4 on: February 17, 2020, 08:05:53 AM »
As stay'tee says, clean the master clip and side plate well with any solvent and seal it with Goop (Shoegoo, plumbers Goop, etc.)!  I actually came back from a run with the clip missing and the pins worn from hitting the chain guard, but the side plate was still intact held only with the Goop.  Had to cut the Goop off to take the side plate off.

Tom
« Last Edit: February 17, 2020, 08:08:32 AM by Koncretekid »
We get too soon oldt, and too late schmart!
Life's uncertain - eat dessert first!

Offline Doc B.

  • Full Member
  • ***
  • Posts: 238
    • Bottlehead Corp.
Re: Motorcycle chain Master link question
« Reply #5 on: February 17, 2020, 01:49:56 PM »
always wipe the outer link surface and clip with Shellite before applying a sealent

For the Yanks - Shellite is what we refer to as Naphtha.

Offline maj

  • Sr. Member
  • ****
  • Posts: 743
Re: Motorcycle chain Master link question
« Reply #6 on: February 17, 2020, 02:32:26 PM »
Lost clips too often, press fit side plates never moved thankfully , we only use rivet links now

Offline 07R1LSR

  • Full Member
  • ***
  • Posts: 124
Re: Motorcycle chain Master link question
« Reply #7 on: February 17, 2020, 04:03:58 PM »
Rivet links it is!

Offline RansomT

  • Sr. Member
  • ****
  • Posts: 559
Re: Motorcycle chain Master link question
« Reply #8 on: February 18, 2020, 10:46:08 AM »
I always use clips BUT I do silicon the clip AND paint the the clip/silicon with high visibility paint.  Never lost one, yet.

Offline wobblywalrus

  • Hero Member
  • *****
  • Posts: 5503
Re: Motorcycle chain Master link question
« Reply #9 on: February 18, 2020, 11:19:31 PM »
One way to keep the clip on is to clean the link real good, apply a dab of JB weld to the side plate while making sure there is good coverage, installing the clip, and smearing on a little bit more JB.  The clip is on permanent so the master link is removed by pushing the pins out from the other side of the chain.  A new master link is needed each time the chain is installed. 

Offline Stainless1

  • Administrator
  • Hero Member
  • ***
  • Posts: 8948
  • Robert W. P. "Stainless" Steele
Re: Motorcycle chain Master link question
« Reply #10 on: February 18, 2020, 11:24:02 PM »
I always use clips BUT I do silicon the clip AND paint the the clip/silicon with high visibility paint.  Never lost one, yet.

I guess the hi-vis paint makes them easier to find on the salt....  :evil:

Over the last 40 years we have only had one clip disappear... the chain stayed together because the plate had to be pressed on the link...  that was 20 years ago... never had the problem again because we switched to rivet style... yes the are one time use, but you don't really need to break the chain a lot. 
Have never been able to make a chain last more than one season anyway...  :cheers:
Stainless
Red Hat 228.039, 2001, 65ci, Bockscar Lakester #1000 with a little N2O

Offline Doc B.

  • Full Member
  • ***
  • Posts: 238
    • Bottlehead Corp.
Re: Motorcycle chain Master link question
« Reply #11 on: February 19, 2020, 11:11:01 AM »
Quote
Have never been able to make a chain last more than one season anyway...

This. The first part to rust, and the worst rust on the whole bike. New ones are only $30 for my bike so I just replace every year. This year I think I will try dipping the new one in paraffin.

Offline Mike Borders

  • Full Member
  • ***
  • Posts: 97
Re: Motorcycle chain Master link question
« Reply #12 on: February 19, 2020, 12:07:51 PM »
Quote
Have never been able to make a chain last more than one season anyway...

This. The first part to rust, and the worst rust on the whole bike. New ones are only $30 for my bike so I just replace every year. This year I think I will try dipping the new one in paraffin.

We switched from Silkolene, an excellent chain lube, to spray-on Chain Wax on our Roadster and our chain never rusts; less messy, too.  Having said that, we still view chains as a consumable and replace them often.

Offline maj

  • Sr. Member
  • ****
  • Posts: 743
Re: Motorcycle chain Master link question
« Reply #13 on: February 19, 2020, 04:00:21 PM »
We have had several seasons from a chain, but it requires remembering to remove it from the bike , cleaning and lubing then storing in a ziplock bag

shortest life we had was less than a meeting on a non oring chain, no way could we keep it lubricated , friction reduction of non o ring was not worth the short life

Offline Stainless1

  • Administrator
  • Hero Member
  • ***
  • Posts: 8948
  • Robert W. P. "Stainless" Steele
Re: Motorcycle chain Master link question
« Reply #14 on: February 19, 2020, 07:51:30 PM »
Yes... quality chain... we stretch cheap chains too fast...
Always pull them off, clean them thoroughly, oil them and throw them in a zip lock with extra oil...
Pull them out the next year, notice they are stiff and rusty... throw them away and put on a new one.  The O-ring and X-ring seem to lock in the salt and lock out the oil...
We can make them run 3 races as long as they are SpeedWeek, World of Speed and World Finals the same year... otherwise they seem to have too much opportunity to rust
 :cheers:
Stainless
Red Hat 228.039, 2001, 65ci, Bockscar Lakester #1000 with a little N2O