Author Topic: How is the timing done?  (Read 19381 times)

0 Members and 1 Guest are viewing this topic.

Offline BranZ

  • New folks
  • Posts: 5
    • http://www.efiperformance.com
How is the timing done?
« on: November 06, 2006, 11:18:42 PM »
The question is:  Do you have only a mile to go has fast as you can?  Do you go from a dead stop or rolling speed?  I just curious on the break out of it all.  P.S. Plan to be there next March!
Just looking for some more speed!

Offline bbb

  • Aerodynamically Challenged
  • Full Member
  • ***
  • Posts: 296
  • JorNic Motorsports
    • JorNic Motorsports, Charlottesville, Va.
How is the timing done?
« Reply #1 on: November 07, 2006, 07:36:27 AM »
here is a video of what it looks like. standing start. this is russ montgomery on a turbo hayabusa at 209mph.

http://s9.photobucket.com/albums/a82/rustman777/?action=view&current=209mphMar06.flv

Offline BranZ

  • New folks
  • Posts: 5
    • http://www.efiperformance.com
How is the timing done?
« Reply #2 on: November 07, 2006, 09:01:19 AM »
So, you start from 0 and have a mile to run as fast as you can?  Shut down area is a half mile? Bad Ass video.  I am already getting pumped for March! BranZ
Just looking for some more speed!

LittleLiner

  • Guest
How is the timing done?
« Reply #3 on: November 07, 2006, 05:37:51 PM »
Long shutdown is closer to 9/10 mile from the finish line.  Oh, . . did we mention the "slight" turn to the right about a quarter mile from the start?  See ya in March...

Offline Waco Racer

  • New folks
  • Posts: 18
How is the timing done?
« Reply #4 on: November 14, 2006, 05:47:24 PM »
You only have 1 mile from a standing start to go as fast as you can. The last 132 feet of the mile is a timing trap that gives an average speed from the first timing beacon to the last. You then have 1/2 mile of paved shut down and another 1/2 mile of gravel and grass to shut down. Look forward to having you.

p.s. LittleLiner is describing Maxton.
NASA Texas Race Director

Offline BranZ

  • New folks
  • Posts: 5
    • http://www.efiperformance.com
How is the timing done?
« Reply #5 on: November 15, 2006, 12:14:14 PM »
It is all I think about.  We are finishing up the paint on my car this weekend. I should have the mechanicals zipped by the end of the year.  I am going to need some time to drive and tune it.  I am basically taking a street car down there.  I will be running a 1991 Z28 with nitrous.  I know that I need Z rated tires but what else?  I just hate to drag it all the way down there and can't run.  What are you running down there? BranZ
Just looking for some more speed!

Offline Glen

  • Global Moderator
  • Hero Member
  • ***
  • Posts: 7024
  • SCTA/BNI timer 1983 to 2004, Retired,. Crew on Tur
how is
« Reply #6 on: November 15, 2006, 02:13:14 PM »
Build it to the SCTA rule book and you will have no problems at any venue.
 :D
Glen
Crew on Turbinator II

South West, Utah

Offline ddahlgren

  • Global Moderator
  • Full Member
  • ***
  • Posts: 272
How is the timing done?
« Reply #7 on: November 16, 2006, 07:34:16 AM »
You might want to have a set of very good brakes compared to the SCTA minimums as they are not needed nearly as much at Bonneville.
Dave

Offline dickj

  • Full Member
  • ***
  • Posts: 107
Re: How is the timing done?
« Reply #8 on: September 30, 2007, 08:19:57 PM »
Timing is by lights at the end of the mile.  The track with the slight turn is Maxton, not the Texas Mile.  The only turn an the Texas Mile is when you leave the shutdown and run into the emergency shutdown.  Hopefully, you never see that turn because it's past the end of the pavement and it's not a good place to be.