(Note: Donations are not tax deductible)

This is a public forum. The opinions expressed here don't
necessarily reflect the feelings of The Folks That Run The Site (that's us)
unless we explicitly say so, ok?


Forum's been "upgraded".
Things will look a bit different.
A *few* posts might have gotten lost in the crossover.
PM bobc with problems, or post in "Website Suggestions".

Author Topic: DYNO TIME NEEDED  (Read 1834 times)

0 Members and 1 Guest are viewing this topic.

Buamotorsport

  • Guest
DYNO TIME NEEDED
« on: February 28, 2018, 12:18:02 AM »
Does anyone in the LA area have or know someone who has a DYNO I can use / rent. It needs to be able to take a blown Hemi. The one I was going to use is now not big enough☹️.

Thanks in advance.

Offline turborick

  • Full Member
  • ***
  • Posts: 198
  • Age: 55
  • Location: Palmdale, Ca
  • Go as fast as we can with as little as we can
    • http://www.bonnevillestreamliner.com
Re: DYNO TIME NEEDED
« Reply #1 on: February 28, 2018, 08:54:04 AM »
are you looking for an engine dyno or a chassis dyno?
Rick Yacoucci

The new Nebulous Theorem 3.5 #788
http://www.bonnevillestreamliner.com

Buamotorsport

  • Guest
Re: DYNO TIME NEEDED
« Reply #2 on: February 28, 2018, 11:36:18 AM »
Engine dyno. It must be able to take a blown Hemi

Offline Dynoroom

  • Global Moderator
  • Hero Member
  • ***
  • Posts: 2095
  • Age: 62
  • Location: Chino Hills, Ca.
Re: DYNO TIME NEEDED
« Reply #3 on: February 28, 2018, 12:01:29 PM »
Contact Brad Anderson in Ontario, Ca.
Michael LeFevers
Kugel and LeFevers Pontiac Firebird

Without Data You're Just Another Guy With An Opinion!

Racing is just a series of "Problem Solving" events that allow you to spend money & make noise...

Buamotorsport

  • Guest
Re: DYNO TIME NEEDED
« Reply #4 on: February 28, 2018, 12:25:08 PM »
Great thanks.

Offline turborick

  • Full Member
  • ***
  • Posts: 198
  • Age: 55
  • Location: Palmdale, Ca
  • Go as fast as we can with as little as we can
    • http://www.bonnevillestreamliner.com
Re: DYNO TIME NEEDED
« Reply #5 on: February 28, 2018, 04:35:24 PM »
here is another one http://www.qmpracing.com/
Rick Yacoucci

The new Nebulous Theorem 3.5 #788
http://www.bonnevillestreamliner.com

Offline Jack Gifford

  • Hero Member
  • *****
  • Posts: 1300
  • Age: 79
  • Location: Phelps, NY
Re: DYNO TIME NEEDED
« Reply #6 on: March 01, 2018, 12:51:25 AM »
... It needs to be able to take a blown Hemi...
That doesn't narrow it down much- could be anything from 50cc to 900 c.i. :wink:
M/T Pontiac hemi guru (or does guru status expire after 30 years?)

Buamotorsport

  • Guest
Re: DYNO TIME NEEDED
« Reply #7 on: March 01, 2018, 12:17:09 PM »
The motor is a 500 cu in aluminium KB ....blown and injected. We are wanting to try different combinations from 485 cu in to 496 cu in to 500.