Author Topic: 2100 CGALT target SW 2013  (Read 4255 times)

0 Members and 1 Guest are viewing this topic.

Offline wheelrdealer

  • Hero Member
  • *****
  • Posts: 1255
  • D/CBGALT
    • WHEELRDEALER RACING
2100 CGALT target SW 2013
« on: October 09, 2012, 06:47:58 PM »
Finally after a year of storing parts... on the 15th I will have a new shop to work out of. My car and a bunch of my parts have been 4 hours away since I moved back to the east coast of Florida last Nov.

My chassis guy called today and the car is finally done...great guy but never again will I tell a chaissis fabricator to take his time, no hurry. I guessed two to four months max...more like 12 months. All is well that ends well.

After the drive shaft let go in 2011 and cut through floor I decided the floor was a very weak part of the car. Rather than replace it with 16 gage sheet metal we went with .125 plate. I got the idea from Jeff's build at BalOSalt. It added about 415 lbs for all the mods mostley the floor and tunnel. We also added a "A" pillar bars and a center Earnhardt bar. Lastly we notched the firewall to make it easier to get to the bell housing bolts.

The chassi guy is confused and asked me if we race over land mines or something.

 

 


 
ECTA    Maxton D/CGALT  Record Holder 167.522
ECTA    Maxton D/CBGALT Record Holder 166.715

WWW.WHEELRDEALER2100.COM

Offline anthony young

  • Jr. Member
  • **
  • Posts: 44
Re: 2100 CGALT target SW 2013
« Reply #1 on: October 10, 2012, 12:57:57 AM »
keep up with the good work ,know your class in the rulebook inside and out and you will be fine, anyone on this site can help with positive info keep your build posted.  anthony young #54 remr :-) 

Offline wheelrdealer

  • Hero Member
  • *****
  • Posts: 1255
  • D/CBGALT
    • WHEELRDEALER RACING
Re: 2100 CGALT target SW 2013
« Reply #2 on: October 10, 2012, 09:22:08 AM »
AY

Thanks, I have learned a lot from this site including a lot about the rule book and how it apply it. My whole idea of the reinforced floor came from Jeff's BalsaSalt build that he posted on the forum. Eventually I want to build a car from the ground up. I was not going to redo the floor in this car but after 2011 drive shaft incedent. It was very obvious in a barrel roll situation the floor was pretty week. So I went ahead and beefed up the floor. In 2011 before Bonneville I added the funny car cage inside the 8 point cage to support the driver's side.

Thanks,

Bill





ECTA    Maxton D/CGALT  Record Holder 167.522
ECTA    Maxton D/CBGALT Record Holder 166.715

WWW.WHEELRDEALER2100.COM

Offline 38flattie

  • Hero Member
  • *****
  • Posts: 2169
    • http://www.flatcadracing.org/
Re: 2100 CGALT target SW 2013
« Reply #3 on: October 10, 2012, 11:20:10 AM »
Looks stout enough!

I'm looking forward to this, as you've sure proven the car can run fast!
With sufficient thrust, pigs fly just fine. However, this is not necessarily a good idea. It is hard to be sure where they are going to land, and it could be dangerous sitting under them as they fly overhead. -- RFC 1925

You can't make a race horse out of a pig. But if you work hard enough at it you can make a mighty fast pig. - Bob Akin

http://www.flatcadracing.org/
http://youtu.be/89rVb497_4c

Offline revolutionary

  • Sr. Member
  • ****
  • Posts: 565
Re: 2100 CGALT target SW 2013
« Reply #4 on: October 10, 2012, 01:00:03 PM »
Lookin good Bill!
Breaking Wind #9614
  ECTA Record AA/BGALT 214.8
  SCTA Bonneville PB AA/BGALT 237.4
Breaking Wind "Spirit of Effluvium" #451
  SCTA Bonneville Record SC/BF100 48.931

Offline Freud

  • Hero Member
  • *****
  • Posts: 5419
Re: 2100 CGALT target SW 2013
« Reply #5 on: October 10, 2012, 02:04:06 PM »
Ray Therat had a drives haft failure in 2011 at WoS.

It just about got him when it came up thru the floor.

He made a major change to get it safe in his 130 Club car.

this also included major strength improvement in the drive shaft.

Bill, you made good decisions.

I'm happy that the car is back in your NEW garage.

FREUD
Since '63

Offline wheelrdealer

  • Hero Member
  • *****
  • Posts: 1255
  • D/CBGALT
    • WHEELRDEALER RACING
Re: 2100 CGALT target SW 2013
« Reply #6 on: October 10, 2012, 03:57:07 PM »
Thanks to alll,

I will post updates and pictures as we make progress. One note, my fab skills are not up to many who post on this forum. With that said, I typically have a large scrap pile.

Bill

ECTA    Maxton D/CGALT  Record Holder 167.522
ECTA    Maxton D/CBGALT Record Holder 166.715

WWW.WHEELRDEALER2100.COM