Landracing Forum Home
November 18, 2017, 08:50:14 AM *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
News:
BACK TO LANDRACING.COM HOMEPAGE
 
   Home   Help Search Calendar Login Register  


(Note: Donations are not tax deductible)







Live Audio Streaming and Archives of Past Events
Next Live Event: TBD
Pages: [1] 2 3 4   Go Down
  Print  
Author Topic: Belly tank diameter question  (Read 8032 times)
0 Members and 1 Guest are viewing this topic.
hotrodderhaag
Jr. Member
**
Offline Offline

Location: N W Pennsylvania
Posts: 34




Ignore
« on: January 15, 2013, 09:20:10 PM »

I found an original aluminum belly tank that can be bought at a reasonable price. .. It is 23" diameter . Is that too small? I was gonna run a ford flathead v8. Please let me know your thoughts and opinions
Logged
Stainless1
Administrator
Hero Member
***
Offline Offline

Age: 66
Location: Wichita KS
Posts: 6451


Robert W. P. "Stainless" Steele Wichita, Kansas



« Reply #1 on: January 15, 2013, 10:06:05 PM »

Start by planning a layout.... do you have a Flathead to work with?  23 is fairly small, so my opinion is it is probably perfect... how long?  Don't forget you can make it an oval if you need width.
Logged

Stainless
Red Hat 228.039, 2001, 65ci, MSA Bockscar Lakester with a little N20 
MSA Bockscar Lakester #1000 my fastest mile 245 and change, 84 ci turbobusa motor... but Corey's 233 MPH H/BFL record is still 3MPH faster than mine.
Jack Gifford
Hero Member
*****
Offline Offline

Age: 77
Location: Phelps, NY
Posts: 1049





Ignore
« Reply #2 on: January 16, 2013, 01:03:49 AM »

... Don't forget you can make it an oval if you need width...
Almost anything can be done with the body for a special-construction category vehicle; just sayin'.
I suggest you study photos of old-time small-tank lakesters, especially those that had flatheads- either sixty-horse or "full size" V8 engines.
Logged

M/T Pontiac hemi guru
DND
Sr. Member
****
Offline Offline

Location: Granada Hills Ca.
Posts: 395





Ignore
« Reply #3 on: January 16, 2013, 05:07:51 AM »

It also depends on how you want to set in the tank, all inside like Markley did or have your head out in the wind or maybe a canopy on top?

Don
Logged
hotrodderhaag
Jr. Member
**
Offline Offline

Location: N W Pennsylvania
Posts: 34




Ignore
« Reply #4 on: January 16, 2013, 06:38:41 AM »

guys,
i have a 1937 21 stud for flathead v-8, trans, and rear end all running ready to go, compleley rebuilt....  id rather have my head out of it with a canopy i belive. the dimenssions of the tank i found are 23"dia x 14.5 feet long... its aluminum.   im buying the tank just cause its a good deal. and i would like to use it, but i almos thought about a fibergalss P38..... this will be my first belly tank build ever so i want it to go somewhat smooth. i know im squeezing ten lbs of Subaru in a five pound bag, but it gonna happen
 
Logged
Dr Goggles
Hero Member
*****
Offline Offline

Age: 167
Location: Melbourne Australia
Posts: 2960


The Jarman-Stewart "Spirit of Sunshine" Bellytank


WWW

Ignore
« Reply #5 on: January 16, 2013, 07:42:33 AM »

Use the one you've found as a cowl..buy a 38 in glass, then you've got a cool lookin tank...
Logged

Few understand what I'm trying to do but they vastly outnumber those who understand why...................

http://thespiritofsunshine.blogspot.com/

Current Australian E/GL record holder at 215.041mph

THE LUCKIEST MAN IN SLOW BUSINESS.
hotrodderhaag
Jr. Member
**
Offline Offline

Location: N W Pennsylvania
Posts: 34




Ignore
« Reply #6 on: January 16, 2013, 08:26:27 AM »

anyone have some good belly tank pictures> p38 style. i googled some.
Logged
dw230
Hero Member
*****
Offline Offline

Location: So Cal & Impound, UT
Posts: 3036





Ignore
« Reply #7 on: January 16, 2013, 11:20:45 AM »

Take a look at the American Hot Rod Foundation site, www.ahrf.com, they have a photo library beyond compare. Contact Jim Miller on that site, he can help locate hat you are looking for.

DW
Logged

White Goose Bar - Where LSR is a lifestyle
Alcohol - because no good story starts with a salad.
Jack Gifford
Hero Member
*****
Offline Offline

Age: 77
Location: Phelps, NY
Posts: 1049





Ignore
« Reply #8 on: January 17, 2013, 01:09:13 AM »

My lakester (pictured in my avatar) uses a fiberglas P-38 replica tank made by ClassGlass in Maryland. It's 36" diameter and 150-some inches long.
Logged

M/T Pontiac hemi guru
wobblywalrus
Hero Member
*****
Offline Offline

Age: 64
Location: backwoods Oregon
Posts: 4438





Ignore
« Reply #9 on: January 17, 2013, 01:18:12 AM »

24 inches is plenty small.  I am not a real big guy at 5'-11 inches and my shoulders are wider than 22 inches with my leathers on.  That's less than an inch clearance on each side at the middle of the tank..   No way I could fit.  You will need some room to fidget. 
Logged
DND
Sr. Member
****
Offline Offline

Location: Granada Hills Ca.
Posts: 395





Ignore
« Reply #10 on: January 17, 2013, 05:22:19 AM »

Plus the frame - roll hoops -padding etc, you would have to be a Tenny-Bopper to even get in the thing !!
Logged
hotrodderhaag
Jr. Member
**
Offline Offline

Location: N W Pennsylvania
Posts: 34




Ignore
« Reply #11 on: January 17, 2013, 06:42:17 AM »

im affraid you guys are correct. i think im gonna go ahead and build one with the p38 tank out of glass........... so that being said. where is the best place to get a  QUALITY fibergalss tank.?
Logged
Captthundarr
Hero Member
*****
Offline Offline

Age: 57
Location: Swansboro, NC
Posts: 1457


In line




Ignore
« Reply #12 on: January 17, 2013, 08:15:33 AM »

Try this fellow, he might be able to help. http://p38-droptank.com/P38-Drop_Tank.html

Elmo Rodge is on the forum.
Logged

Live,Laugh, Love /  Jack Scratch Racing /ECTA   
Amy Hartman-Driver, Frank Hartman-everthing else.
C/GALT 137.65 Ohio Mile check that 144.12 2013, AA/GALT 159.34 Ohio Mile 2014. B/GALT 180.577 RECORD 6/15
dw230
Hero Member
*****
Offline Offline

Location: So Cal & Impound, UT
Posts: 3036





Ignore
« Reply #13 on: January 17, 2013, 11:36:25 AM »

Elmo's tanks are off the forms developed by the late Jack Kelly. Jack's tank, NOT tanker  angry, is the beautiful, yellow #64. The car has been in storage since Jack's passing. There are plans to move it to White Goose Bar World Headquarters for a refurbishing by the craftsmen on that team.

There may be beer involved.

DW
Logged

White Goose Bar - Where LSR is a lifestyle
Alcohol - because no good story starts with a salad.
hotrodderhaag
Jr. Member
**
Offline Offline

Location: N W Pennsylvania
Posts: 34




Ignore
« Reply #14 on: January 17, 2013, 12:54:41 PM »

youll never hear me say TANKER... not intentionally anyways.


well i did some research.. found this company.
http://www.gothamcruisers.com/index.htm

they make a p38 tank with head rest for $1100.
and its nice looking,

they are using this companies tank in the build below:
http://www.jalopyjournal.com/forum/showthread.php?t=763913

and so far they are reslly happy with it from what im told.... other companys are at 1250 or higher for a glass p38 tank... and the gotham cruisers are about 4 hours from me, so i think i may order one from them and maybe take a tour of the place. from what i see and how they talk, they are  good at what they do.
« Last Edit: January 17, 2013, 01:02:03 PM by hotrodderhaag » Logged
Pages: [1] 2 3 4   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!


Google visited last this page June 17, 2017, 04:35:52 PM